SHOP BY PART

  1. C5 Corvette T1 Hood Louvers Kit

    $359.99
    • Designed specifically for the C5 corvette hood lines and low pressure zones behind the radiator and above the wheel arches. Dimensions: Center Vent
    • 13" Height
    • 15" Front Width
    • 20" Rear Width Side Vent
    • 17" Height
    • 11" Front Width
    • 9" Rear Width Learn More
  2. 03-04 Mustang Cobra Hood Louver Kit

    $219.99
    • Direct Replacement, no cutting required!
    • Installs in about 10 minutes.
    • Designed specifically for 03-04 Cobra mustang hoods.
    • Replaces factory non functional plastic vents with functional heat extractors.
    • Made of aircraft grade aluminum to increase strength and reduce weight.
    • Replace your broken plastic cobra hood vents with functional heat extractors!
    • This kit includes both driver and passenger hood vents, hardware, and backing plates.
    • May fit aftermarket cobra hoods that accept factory plastic vents.
    Learn More
  3. C5 Corvette T1 Side Louver Set includes 2 side vents from T1 kit. DOES NOT include the T1 center vent.
  4. Designed specifically for the C5 corvette hood lines and low pressure zones behind the radiator and above the wheel arches. Dimensions:
  5. 17" Height
  6. 11" Front Width
  7. 9" Rear Width Learn More
  • C3 Corvette L88 (Long Version) Hood Louver Kit

    $229.99
    • Designed specifically for the C3 corvette with L88 Hood power bulge as seen in photos and low pressure zones behind the radiator.
    • Also fits cowl style hood of later C3 corvettes. Please check measurements before ordering or contact us.
    • Measurements: 15.5" wide and 15.5" tall with V shape.
    • Includes 1 center section vent with all installation hardware.
    • WARNING!!! NOTE: The louvers protrude below the hood surface approx. 7/8". Be sure to check hood clearance to assure there will not be clearance issues. Some high rise manifolds and air cleaners may interfere so please check! Dimensions:
    • 15.5" Height
    • 15.5" Front Width
    • 15.5" Rear Width
    Learn More
  • This includes just the center vent from the GT2 kit for the 2005-2009 Mustangs.
  • This does not include the side vents. Dimensions:
  • 13" Height
  • 15" Front Width
  • 20" Rear Width Learn More
  • Designed specifically for the fifth generation Camaro's hood lines and low pressure zones behind the radiator and above the wheel arches. This kit only includes a center section.
  • NASA Legal for ST2 area requirements.
  • Same product used on Russ Taylor's podium winning ST2 Z28 in NASA West Coast Championship.
  • This product does fit early 5G Camaro SS Hoods Dimensions:
  • 25.5" Height
  • 20.5" Front Width
  • 23.25" Rear Width Learn More
  • New Pontiac GTO Hood Vent Kit (04-06)
  • Designed specifically for the Pontiac GTO hood lines and low pressure zones for maximum heat extraction.
  • This kit includes a pair of left and right hood vents that install on top of the existing GTO hood nostrils.
  • NASA Legal for ST2 area requirements. Dimensions:
  • 18.9" Height
  • 8.33" Front Width
  • 10" Rear Width Learn More
  • New Nissan 370Z Hood vent kit
  • Designed specifically for the 370Z hood lines and low pressure areas.
  • Includes a center vent and 2 side vents. Use options below to change configuration.
  • NASA Legal for ST2 area requirements. Dimensions: Center Vent
  • 14.5" Height
  • 18.5" Front Width
  • 23.1" Rear Width Side Vent
  • 17" Height
  • 5.5" Front Width
  • 6.0" Rear Width Learn More
  • New C6 Corvette Fender vents

    C6 Corvette Fender vents

    $249.99
    • Designed specifically for the C6 Corvette fender area to extract pressure.
    • Includes a driver and passenger side fender vent.
    Learn More
  • New BMW E90 E92 M3 Hood Vent Kit
  • Designed specifically for the E90/E92 generation M3 hood lines and low pressure zones behind the radiator. This kit only a center section and 2 side vents. Dimensions: Center
  • 9.5" Height
  • 20" Front Width
  • 23" Rear Width Side Vent
  • 19.75" Height
  • 7" Front Width
  • 8.25" Rear Width Learn More